Boost gauge hose barb size?
#1 by
Yoda
, Sat Aug 25, 2012 3:41 pm
Is there a standard size for the hose barb on the back of a boost gauge? The one I have is 4mm with the vernier. But our vac system seems to be 4.7mm or more accurately 3/16. Do I get a silicone hose to fit the boost gauge and just stretch it over the T piece?
"LS200" - 1UZ V8, auto tiptronic, super select, Upol Raptor paint. Bigger, faster, louder, brighter.
- Yoda
-
Posts: 5.855 Date registered 10.16.2011
RE: Boost gauge hose barb size?
#2 by
123hotchef
, Sat Aug 25, 2012 4:06 pm
i JUST DIPPED my hose in a cup of boiling water it streched over the T piece easily.
As long as you dont have a leak it should be fine.
Tight is always good
AREA REPRESENTATIVE: South East England
'PYROCHEF'
- 123hotchef
- Forum Legend
-
Posts: 34.246 Date registered 02.15.2012
RE: Boost gauge hose barb size?
#3 by
Yoda
, Sat Aug 25, 2012 5:06 pm
That's what I was thinking. Just wanted to check that people be doing the same.
"LS200" - 1UZ V8, auto tiptronic, super select, Upol Raptor paint. Bigger, faster, louder, brighter.
- Yoda
-
Posts: 5.855 Date registered 10.16.2011
RE: Boost gauge hose barb size?
#4 by
fatboy
, Sat Aug 25, 2012 8:03 pm
Quote: Yoda wrote in post #1
Is there a standard size for the hose barb on the back of a boost gauge? The one I have is 4mm with the vernier. But our vac system seems to be 4.7mm or more accurately 3/16. Do I get a silicone hose to fit the boost gauge and just stretch it over the T piece?
4.7mm seems a bit large. I've only used 3.5mm and 4mm when replacing all the vac hoses on Big Truck
Big Truck
53 plate Animal
Mountain top with 3" roll bar
8" spots on bar
Front over rider with more spots
Decatted
Egr removed
Osram nightbreakers fitted
1 Dead engine
It's Aliveeeeeeeeeeeeeee!
- fatboy
-
Posts: 976 Date registered 11.20.2011
RE: Boost gauge hose barb size?
#5 by
Yoda
, Sat Aug 25, 2012 8:06 pm
Measured the hose barbs and inside of the hose with a vernier. Could be that FBW has different sized vac system?
"LS200" - 1UZ V8, auto tiptronic, super select, Upol Raptor paint. Bigger, faster, louder, brighter.
- Yoda
-
Posts: 5.855 Date registered 10.16.2011
RE: Boost gauge hose barb size?
#6 by
fatboy
, Sat Aug 25, 2012 8:11 pm
Did not think of that 
Keep forgetting you are old school 
Big Truck
53 plate Animal
Mountain top with 3" roll bar
8" spots on bar
Front over rider with more spots
Decatted
Egr removed
Osram nightbreakers fitted
1 Dead engine
It's Aliveeeeeeeeeeeeeee!
- fatboy
-
Posts: 976 Date registered 11.20.2011
RE: Boost gauge hose barb size?
#7 by
LezT
, Sat Aug 25, 2012 8:12 pm
Should all be the same, just warm up a bit of 4mm
K74 02 plate
Shoggy Sport 3.0 v6
2E0LEZ
Kenwood TS670.. Yaesu FT575GX.. YaesuFT8800D.....Yaesu FT897
Yaese FT101ZD......20M BitX3C TXRX
Kenwood Chef.....Goblin Teasmaid
“If electricity comes from electrons, does morality come from morons”
FORUM MODERATOR...
- LezT
- Forum Legend
-
Posts: 18.434 Date registered 10.01.2011
RE: Boost gauge hose barb size?
#8 by
Yoda
, Sat Aug 25, 2012 8:19 pm
No worries. I ordered 4 and 3/16 just in case.
"LS200" - 1UZ V8, auto tiptronic, super select, Upol Raptor paint. Bigger, faster, louder, brighter.
- Yoda
-
Posts: 5.855 Date registered 10.16.2011
RE: Boost gauge hose barb size?
#9 by
123hotchef
, Sat Aug 25, 2012 8:23 pm
its probably mostly made in China anyways
AREA REPRESENTATIVE: South East England
'PYROCHEF'
- 123hotchef
- Forum Legend
-
Posts: 34.246 Date registered 02.15.2012
RE: Boost gauge hose barb size?
#10 by
ColinTheCop
, Sun Aug 26, 2012 11:46 am
More importantly, what colour did you order...?
05 Warrior
- ColinTheCop
-
Posts: 2.901 Date registered 11.20.2011
RE: Boost gauge hose barb size?
#11 by
Yoda
, Sun Aug 26, 2012 11:56 am
Red!
"LS200" - 1UZ V8, auto tiptronic, super select, Upol Raptor paint. Bigger, faster, louder, brighter.
- Yoda
-
Posts: 5.855 Date registered 10.16.2011
