I will sell it if anyone is interested dont bother me none

boost gauge in just waiting for oil pressure gauge now decided to mount that far right of binnical

And in the centre?

probaby just keep it as outside temp for now anyway got some ideas in the pipe line

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

How about a nice dual readout of water temps upper and lower.

Werbung: http://www.ebay.co.uk/itm/331393516805?_...K%3AMEBIDX%3AIT

ha ha that what my thinking mate how did ya know one it the bottom rad hose and one in the top rad hose to monitor the temps as the gauge in the dash is crap

I've had new batteries installed in my crystal ball fella. Did this with mine 'coz as you rightly say, the stock gauge is pants.

got any pics of urs mate? i was thinking a rectangle one but it would look poo as the binical hole is round but it is bigger than the other 2 holes

the dash gauge dont move until its too late IMO

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

Werbung: ZwAAOSwQPlV7cvq" target="_blank">http://www.ebay.co.uk/itm/Koso-Race-Trac...ZwAAOSwQPlV7cvq

Replaced the single measurement one i put i the dash a while back. Think there's pics of it in the "What have you done to your truck blog". Dont think ive got any pics of the double one as yet. You could always make a black backing template to change the binacle hole to a 52mm. Only a matter of cutting out a bit of black plastic and bonding it to binacle to leave the 52mm viewing hole.

Hmmm.... Rectangle one looks ok, but yeah, would probably look poo in the standard binacle.

yeh round it is i think did u get the one u linked too @spud

Certainly did Cheffy. Took about 10 days to get here if i remember right.

taiwan! that means my oil pressure gauge will be here next week then! did you get aloy inserts for ya rad hoses with tapped out inserts too?

Nope i cheated. I dont like the inserts so i piggybacked the original top aircon/water temp sensor and then tapped out the thermostat housing to take another temp sensor.

Cheater the thermostat housing aint really the best place for the sender sensor though

It is if you place it in the housing before the actual thermostat. The housing that the bottom rad hose fits onto. Is the same as placing an insert into the lower rad hose but with far less worries of things like clips corroding or leaks from pipe to insert.

So u just drilled it and tapped it out then

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

Yup. Just looking at your housing which appears shallower to mine ( mine has different w/pump to yours .) Should still be possible but you're gonna need to go in more horizintally i reckon. Take a look.. Werbung: http://www.ebay.co.uk/itm/MITSUBISHI-L20...gIXALI_OuItJz7w

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

Werbung: http://www.ebay.co.uk/itm/MITSUBISHI-L20...EQAAOSwcnpToKWM

Hmm... Could be just that piccy though as this one looks deeper so you should have an easier job.

Wenn Sie hier auf Links zu eBay klicken und einen Kauf tätigen, kann dies dazu führen, dass diese Website eine Provision erhält.

----> Werbung: http://www.ebay.co.uk/itm/Mitsubishi-Del...soAAOSwZd1Vc4lI My shape pump.

wow didnt realise they are so different

I might get a metal piece for the bottom hose as the hose is kinked from the 3" lift any way and a metal insert will fix that kink if done right
2 birds one stone

Ran the wires for the light bar and work lights today

wish these relays would hurry up from china