Front panel
#1 by
robl200
, Sat Dec 22, 2012 10:31 am
Ordered a new front panel today as mine is rather transparent and a little bent out of shape following a bit of over enthusiasm leaving Cadgers brae car park..... Oops!
Once it arrives I'll just have to work out how to stick it on....
Y reg trojan 184k now sold after 8 years of off road shenanigans and rebuilds and laffs!!
02 4life 72k in pieces!!
- robl200
-
Posts: 3.540 Date registered 10.02.2011
RE: Front panel
#2 by
warriortom
, Sat Dec 22, 2012 10:53 am
I could do with knowing the same info as mine has got a hole in it
03 warrior..
-32 offset black mods, decat fitted, egr blanked and cooler removed, 265/75/16 kingpin MT tyres,
Next on the list... Fit 25mm body lift and add some green bits!!
- warriortom
-
Posts: 690 Date registered 07.19.2012
RE: Front panel
#3 by
billymadbiker
, Sat Dec 22, 2012 10:59 am
It's mostly held on by spot welds.
When you get the new one it will have holes in it for the welds, find these on your existing panel and drill them out with a spot weld cutter.
Clean off the paint/rust and stick the new one back in the same place.
Normally you would put some tacks on then check the bonnet catch etc all lines up ok before welding proper.
- billymadbiker
-
Posts: 893 Date registered 03.06.2012
RE: Front panel
#4 by
robl200
, Sat Dec 22, 2012 11:36 am
Cheers for that, all the replacement panels I've seen come as one section. Mine is a mess from below the lights really...
Y reg trojan 184k now sold after 8 years of off road shenanigans and rebuilds and laffs!!
02 4life 72k in pieces!!
- robl200
-
Posts: 3.540 Date registered 10.02.2011
RE: Front panel
#5 by
woody13
, Sat Dec 22, 2012 11:44 am
Quote: robl200 wrote in post #1
Ordered a new front panel today as mine is rather transparent and a little bent out of shape following a bit of over enthusiasm leaving Cadgers brae car park..... Oops!
Once it arrives I'll just have to work out how to stick it on....
Mines invisible,Dave at D.T. is rebuilding the whole lower front end on mine in the new year.Its gonna be a lot stronger than factory....
FORUM AREA REPRESENTATIVE - North West England
2.8 Import,gone but not forgotten...
The Beast,never to be forgotten...
The Big Silver Beastie,soon to be reborn...
The Frankenfender is on its way....
- woody13
- Forum Legend
-
Posts: 12.549 Date registered 10.05.2011
RE: Front panel
#6 by
warriortom
, Sat Dec 22, 2012 1:00 pm
The part numbered 62650 is the bit that is rotton on mine. Does this mean i could just get that part replaced???
03 warrior..
-32 offset black mods, decat fitted, egr blanked and cooler removed, 265/75/16 kingpin MT tyres,
Next on the list... Fit 25mm body lift and add some green bits!!
- warriortom
-
Posts: 690 Date registered 07.19.2012
RE: Front panel
#7 by
LezT
, Sat Dec 22, 2012 1:08 pm
Spot weld drills available from BealUK
K74 02 plate
Shoggy Sport 3.0 v6
2E0LEZ
Kenwood TS670.. Yaesu FT575GX.. YaesuFT8800D.....Yaesu FT897
Yaese FT101ZD......20M BitX3C TXRX
Kenwood Chef.....Goblin Teasmaid
“If electricity comes from electrons, does morality come from morons”
FORUM MODERATOR...
- LezT
- Forum Legend
-
Posts: 18.434 Date registered 10.01.2011
RE: Front panel
#8 by
baz
, Sat Dec 22, 2012 8:27 pm
Werbung: http://www.ebay.co.uk/itm/6-0MM-SPOT-WEL...=item3a471fef24
51 plate tinted glass alloys 
side steps roll bar rear step wind gards
roller shutter bed rug
- The following contents have been linked to this post::
- baz
-
Posts: 698 Date registered 10.03.2011
