Stared at mine last night, dropped my new engine crane at my dad's (where the truck is), can't wait for sunday so i can try and set the engine timing and see if that helps my engine knock.

Went to weld on my rock sliders but found we've run out of gas so fitted my wind deflectors instead. They were a bargain team heko smoked wind deflectors off gumtree brand new in box for £15...

Crank pulley done, new alternator belts and pas belt

Also fitted a new t handle lock in the canopy. Happy days

Well where shall I start??
This week triggers broom has had the front brakes sorted with new carriers, slide pins (as the slide pins where seized in the carriers), pads then to top it off the starter motor stopped working.

Re-located my front bumper after doing the body lift last week. I think it is a unique idea by mitsubishi to use shear bolts on every single component that is located under the truck ! ! !

Quote: JasonK wrote in post #753

---

Crank pulley done, new alternator belts and pas belt

Also fitted a new t handle lock in the canopy. Happy days

---

Quote: Hound Dog wrote in post #754

---

Well where shall I start??
This week triggers broom has had the front brakes sorted with new carriers, slide pins (as the slide pins where seized in the carriers), pads then to top it off the starter motor stopped working.

---

Quote: bart wrote in post #755

---

Re-located my front bumper after doing the body lift last week. I think it is a unique idea by mitsubishi to use shear bolts on every single component that is located under the truck ! ! !

---

Treated my old girl to a new fuel filter and filter head just the oil and filter to do , fitted a mitsubishi upgrade chip and am well impressed. The twilight zone at low revs has gone and its a lot more drivable around town , just have to wait and see if lunches the engine . Only have the actuator on the axle to look at and I am ready for winter

@123hotchef the starter wouldn't engage properly to start the truck. And couldn't wait for Mitsubishi to get the spares in as its my daily drive and needed for work.

All filters, oils (diffs, engine, transmission) all levels, greased props except the wee front one cos its got a stupid nipple ... my truck loves me now

Changed front brake pads because of the squeaking.... and found out its the rear ones that are make all that noise.... DOH!

Bought it

Fitted my lezt bonnet struts

Fitted a new bed liner and dog mat!

Fitted my Cree spot lamps in....

Not done anything to mine cause i dont have one.I did abuse the car today and the engine management light is on now lmao

Quote: stormforce wrote in post #765

---

Not done anything to mine cause i dont have one.I did abuse the car today and the engine management light is on now lmao

---

Quote: Pugs wrote in post #766

---

Quote: stormforce wrote in post #765

---

Not done anything to mine cause i dont have one.I did abuse the car today and the engine management light is on now lmao

---

---

I drove 300 miles in mine today & averaged 33mpg.

nothing had the engine out of the car sump off subframe down and changed out the pick up due to low oil pressure gotta put it all back together tomorrow learnt alot though

New A bar is bolted on and had to adjust the turbo again due to over boost , starting to think the turbo is full of crud and sticking

Rust protected my "new" gearbox cross member, the last one looked like a twisted U after some rock climbing two weeks ago.

Finally got round to fitting my winch rope. (@123hotchef the new winch is still in the box minus the rope.)

Sold it

Quote: Rob1307 wrote in post #770

---

New A bar is bolted on and had to adjust the turbo again due to over boost , starting to think the turbo is full of crud and sticking

---

Quote: Hound Dog wrote in post #772

---

Finally got round to fitting my winch rope. (@123hotchef the new winch is still in the box minus the rope.)

---